THE PARK LOBBY / RESTROOM
THE PARK LOBBY / RESTROOM is a renovation/alteration project at 8300 N MOPAC EXPY, Austin, in Travis County, TX, tracked from its Texas Department of Licensing and Regulation (TDLR) registration. Construction complete (TDLR inspection passed Jul 2023). The project has an estimated value of $650K across about 4,673 sq ft.
📊Project Metrics
TDLR #TABS2023013915Project Closed
Project has been completed and closed
THE PARK LOBBY / RESTROOM is a Renovation/Alteration project located at 8300 N MOPAC EXPY, Austin, TX 78759 in Austin, Texas. The project has an estimated value of $650K covering 4,673 sq ft. OP 8300 MOPAC PROPERTY LLC C/O LUKE PHILLIPS is the property owner and RED DESIGN STUDIOS is the design firm of record. The project was registered with TDLR on March 13, 2023.
❓Frequently Asked Questions
What is THE PARK LOBBY / RESTROOM?
THE PARK LOBBY / RESTROOM is a renovation/alteration project at 8300 N MOPAC EXPY in Austin, Texas, registered with the Texas Department of Licensing and Regulation (TDLR). Scope of work: THIS PROJECT CONSISTS OF THE DEMOLITION, UPGRADE AND FINISH OUT OF EXISTING BUILDING LOBBIES, CORRIDORS AND LEVEL 2 RESTROOMS. OCCUPANCY CLASSIFICATION AND USE GROUP REMAINS UNCHANGED BY THE SCOPE OF THIS WORK.
Is THE PARK LOBBY / RESTROOM open in Austin?
Construction on THE PARK LOBBY / RESTROOM is complete — TDLR records show the project passed its required accessibility inspection in Jul 2023. The building is finished and very likely open.
Where is THE PARK LOBBY / RESTROOM located?
THE PARK LOBBY / RESTROOM is located at 8300 N MOPAC EXPY, Austin, TX, 78759, in Travis County.
Who is the owner or developer of THE PARK LOBBY / RESTROOM?
OP 8300 MOPAC PROPERTY LLC C/O LUKE PHILLIPS is the property owner/developer of record for THE PARK LOBBY / RESTROOM, per its TDLR project registration.
Who is the architect or design firm for THE PARK LOBBY / RESTROOM?
RED DESIGN STUDIOS is the design firm of record for THE PARK LOBBY / RESTROOM, according to its TDLR filing.
How much does THE PARK LOBBY / RESTROOM cost and how big is it?
THE PARK LOBBY / RESTROOM has an estimated construction value of $650K and approximately 4,673 square feet (about $139/sqft), based on its TDLR filing.
📋Scope of Work
THIS PROJECT CONSISTS OF THE DEMOLITION, UPGRADE AND FINISH OUT OF EXISTING BUILDING LOBBIES, CORRIDORS AND LEVEL 2 RESTROOMS. OCCUPANCY CLASSIFICATION AND USE GROUP REMAINS UNCHANGED BY THE SCOPE OF THIS WORK.
Note: This project is registered under the Texas Accessibility Standards (TAS) program. TDLR registration is required for commercial and public facility construction to ensure compliance with accessibility requirements under Texas Government Code Chapter 469.
📅Compliance Timeline
📅Project Timeline
Filed
Mar 13, 2023
Review Complete
Inspection Complete
Closed
Jul 3, 2023
🔗Related Projects
👤Same Owner
$2.0M total📄Related City Permits
Building permits found at or near this location
Replacement of complete existing central heat and air system with or without duct work Replacement of HVAC system.
Replacement of complete existing central heat and air system with or without duct work
EXPRESS: Foundation repair
Addition of a rear patio cover - minor electrical
PROJECT SCOPE Provide one new dedicated AFCI/GFCI protected 20A 120V branch circuit from the main panel on the exterior wall of the house to a new kitchen range hood. No meter work being performed. INSTALLATION DETAILS Install a vertical 1-inch Steel EMT raceway exiting the main electrical panel from a 1-inch LR conduit body (located below all energized parts) on the homes exterior brick wall. Transition raceway to horizontal orientation for building penetration using a 1 LB. Penetrate into the accessible attic with 1 EMT terminating into a 4-11/16 steel junction box with a blank cover. Install #10-2 UF-B cable (1 HOT 1 NEUTRAL 1 EGC) (Sunlight Resistant/Wet Location rated) from the range hood to the steel junction box. Cable will be routed along ceiling rafters; any portion below 7 will be protected by guard strips per NEC 320.23. The #10-2 UF-B will be sleeved continuously from the 4-11/16 junction box through the LB down the vertical EMT and through the LR terminating directly into the main panel . This avoids all splices providing a continuous run from the OCPD to the appliance. CODE COMPLIANCE NOTES: 10 AWG conductors are specd. for this 20A circuit to account for ambient temperature correction in the unconditioned attic and sun-exposed exterior raceway. The EMT will be sealed with duct seal at the attic box and panel entry to prevent moisture migration and condensation per NEC 300.7. All cables and raceways will be supported/secured per NEC. All exterior fittings/hardware will be UL-listed rain-tight compression type. All cables and raceways will be supported and secured per NEC requirements. An insulated throat fitting or plastic bushing will be used at all EMT entry points to protect the cable jacket from abrasion. All wire terminations will be torqued to the manufacturer specifications per 2023 NEC 110.14(D)